Color DSP CCD Camera
Thank you very much for purchasing our product. Before operating this product, please read this instruction manual carefully to ensure proper use. 1. Safety Precautious
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems). Please avoid places where there is direct sunlight If any abnormality occurs, make sure to unplug the unit and contact your local dealer. When using this Camera in places where the lighting differs greatly, please use an Auto Iris Lens with a ND Filter. Please avoid places where temperatures exceed 50 or more, high humidity and/or direct rainfall, frequent vibrations, or shocks occur. If the minimum brightness of 0.1 Lux cannot be achieved, install the appropriate light fixtures. When the Camera is not used, keep the lens or the lens cap attached to protect the CCD Sensor. The color camera uses SONY high sensitive super HAD 1/3? interline Charge Coupled Device (CCD) image sensor, employs Digital Signal Processor (DSP) chip-set for image control, and all integrated state circuitry which provides extremely long life and high reliability. High resistance shock and vibration, easy to install, this camera is a very good choice for your color CCTV system.
Color camera with a SONY 1/3? Super HAD CCD sensor. Employed Digital Signal Processor()chip-set for image Pixel Number: NTSC=380K / PAL=440K (High Resolution) NTSC=270K / PAL=320K (Normal Resolution) High Sensitivity, Low Smear, High Anti-Blooming, and a high S/N ratio. Functions Supported: Auto Electronic Shutter (AES), Auto ), Auto Gain Control (AGC), Auto White Balance (AWBManual White Balance (), Back Light Compensation (Flickerless mode (), Line lock (for AC-Type only). Supports Auto Iris Lens: both Video-Drive & DC-Drive lens. Supports both C and CS mount Lenses. Built-in anti-aliasing and IR-cut optical filter.
4. Name of Each Parts
5. Installation & Operation Please refer to Fig. 1 or Fig. 2 (P3) and setup guide below: 1. Remove the cap cover from the top of the lens mount. 2. Screw the lens into the lens mount. 3. Connect the video output (9) to the monitor or other video device through a 75 Ohms type coaxial cable. 4. Connect the power source (6), AC with the power cord, or DC by using the DC Jack (+12V DC in jack center), then the LED indicate (7) will lit. 5. Once the picture appears on the monitor, adjust the focus and iris of the lens to obtain the best picture. 6. If the subject is not in correct focus when adjusting focus of the lens, do back focus adjustment as following: Set the focus ring of the lens to indefinite position. Take picture of subject at a distance more than 20M away. Loosen the lens mount fixing screw (use L-wrench). Turn the lens and the lens mount together, so that the subject is in focus and the picture is clear. Screw the lens mount fixing screw. 7. Mount the camera on the mounting bracket by using the hole (1) on top or bottom of the camera or using the enclosed 8 mm mounting block with the 2 screws furnished. 8. DIP Switch (2) Setting AWB/ MWB FUNCTION AWB mode–In this mode, camera automatically aligns the white balance, the operation color temperature range is from approximately 2500K to approximately 9500K. MWB mode–In this mode, you can use MWB/ Phase (8) up-key and down-key to adjust color the temperature from approximately 2500K to approximately 9500K. AUTO IRIS FUNCTION When using an auto iris lens, DIP S.W switch (2) should be in position with OFF to disable AES function. Before plugging the enclosed miniature 4 pins to the auto iris connector (4), please check the type of auto iris lens, and also the compatibility on the polarities.
If the auto iris lens is setup to the DC Drive (or Direct Drive), the Switch (5) should be in position with the DC Drive. Adjust the VR (3) to the proper level. If video drive iris lens is used, the switch (5) should be in position with the Video DR. When using manual iris lens, DIP S.W switch (2) is select-able depending on the environment. BLC FUNCTION Set switch-OFF/ BLC to BLC to enable back light compensation (BLC) function. AGC-HI / AGC-LO FUNCTION AGC maximum gain setup to high/ low (AGC-Hi mode–The maximum AGC gain is approximately 26dB. AGC-Lo mode–The maximum AGC gain is approximately 16dB). FLICKERLESS FUNCTION Set the switch-OFF/ FLON. Set to FLON to enable flickerless function, in this mode, the switch-AES/ OFF is auto disabled. LINE LOCK FUNCTION (for AC-Type only) When using line lock function, the switch-INT/L.L. should be in position with L.L. and adjust MWB/ Phase (8), use up-key and down-key to adjust the proper phase (Note: If you want to adjust the phase, the switch-AWB/ MWB should be in position with AWB).
6. Auto Iris Control PinVIDEO DRIVER (Direct DRIVE)
1 2 3 4 IRIS OUT
Auto Iris Lens Connector 1 Camera 1 Allen Wrench 1 4-Pin Connector for Auto Iris Lens 1 Instruction Manual
8. Specification Image Device 1/3? Color Sony Super HAD 1/3? Color Sony Ex-View Super HAD1/3? Color Sony Hi-Res. Super 1/3? Color Sony Hi-Res. Ex-View Super HAD
Picture Elements NTSC482, PAL
Resolution 380 TVL 470 TVL
Min. Illumination 0.1 Lux/ F1.2 0.05 Lux/ F1.2 0.2 Lux/ F1.2 0.07 Lux/ F1.2
S/N Ratio more than 48 dB.
Electronic Shutter NTSC:1/60s~1/100,000s, PAL:1/50s~1/110,000s
Flickerless Mode NTSC: 1/100s, PAL:1/120s (ON/OFF Switch-able)
Iris Control Video/ DC-Drive
Lens Mount C/ CS
Gain Control Hi/ Low
White Balance Auto/ Manual
Back Light Comp. On/ Off
Sync. System Internal/ Line Lock (for AC type only)
Video Output 1 Vp-p/ 75 Ohms
Power Supply 10%, AC24V, AC110V, AC100~240V (optional)
Power Consumption DC/ 250mA max.AC/ 4.5W max.DC/ 295mA max. AC/ 5W max.DC/ 250mA max.AC/ 4.5W max.DC/ 295mA max.AC/ 5W max.
Operating Temp. -10 to 50 (14 to 122
Note: Design and specifications are subject to change without prior notice.
Para poder atenderte mejor necesitamos conocer: